Technical Drawing
备注
- 带液晶显示的计数器
- 信号输出插座(簧片触点)
- 进气口
- 出气口
- 灌装螺塞
- 进气通道
- 套管
- 底盘
- 微毛细管
- 两个簧片触点
- 永磁体
- 包装液
- 带双室的测量单元(倾斜体)
- 液位跟踪螺丝
- 检查螺杆进气通道
性能数据
最小流量 Qmin | 1 | ml |
最大流量 Qmax | 1 | ltr/h |
测量精度 (1) | ±3 | ±1 | % |
测量鼓容积, 大约 (2) | 3 | ml |
最小 测量体积(分辨率) (3) | 3 | ml |
封闭液体体积,约 | 120 | ml |
直径 | 98 | mm |
高度 | 109 | mm |
重量 | 475 | g |
最大进气压力 | 100 | mbar |
最小进气压力 | 8 | mbar |
开始测量时的进气压力 (5) | 9 | mbar |
气体温度 (4) | +10 至 +60 | °C |
最小刻度盘划分 (6) | 0.01 | ml |
最大指示值 (6) | 999,999.99 | ml |
连接气体入口和出口 | 螺纹式管接头 | |
外径Ø | 6 | mm |
内径 | 4 | mm |
- (1) Because of the physical measurement principle, the measurement error is dependent on the flow rate. The data acquisition software »RIGAMO« (accessory) provides an algorithm, which automatically recalculates the actual measurement data to the real values at the respective actual flow rate on the basis of the calibration curve. Thus, the remaining error can be reduced significantly or the flow rate range can be extended at the constant measurement error of ±3%. The remaining error is better than approx. ±1% across the full flow rate range.
- (2) = 名义值; 准确值将通过单独校准确定
- (3) = 测量室容积
- (4) 对于完整的MGC适用: 当温度>室温时(如放在加热炉中),在这种特殊情况下,会监测到封闭液体形成泡沫。
- (5) 如果以高流速开始测量,则可能需要增大最小进气口压力。 在这种情况下,需要更高的压力,直到基板中的微毛细管中没有封闭液体残留为止。
- (6) 由于带有小数点后两位的校正系数
模型 (Materials)
V 3.4 / Rev. 2023-03-08 / 如有变更以新版为准。
本数据表的最新版本可在以下网站找到。 …
https://dlr.ritter.de/zh-hans/milligascounter-mgc-1-pmma/
Dr.-Ing. RITTER Apparatebau GmbH & Co. KG · Coloniastrasse 19-23 · D-44892 Bochum · 德国
如有疑问,请联系 mailbox@ritter.de 或您当地的分销合作伙伴 (在我们的概述页面上)
https://dlr.ritter.de/zh-hans/milligascounter-mgc-1-pmma/
Dr.-Ing. RITTER Apparatebau GmbH & Co. KG · Coloniastrasse 19-23 · D-44892 Bochum · 德国
如有疑问,请联系 mailbox@ritter.de 或您当地的分销合作伙伴 (在我们的概述页面上)